How to Fix MySQL Error 1610 (ER_SLAVE_CORRUPT_EVENT)
A corrupted replication event triggers mysql error 1610 when a replica reads bad log data. You fix this error by resetting the replica position to a clean binary log file. Database clusters rely on binary logs to copy changes from a primary server. When a replica receives damaged log events, it stops work right away. This stop protects your replica tables from bad writes and missing rows. Teams must find the exact break point to restore normal data flow. What causes mysql error 1610 in databa
Your coding agents run with your access.
Claude Code reaches prod with a developer's credentials, and approval prompts get clicked through. hoop.dev checks every query, masks sensitive data, and holds risky changes for a human.
A corrupted replication event triggers mysql error 1610 when a replica reads bad log data. You fix this error by resetting the replica position to a clean binary log file.
Database clusters rely on binary logs to copy changes from a primary server. When a replica receives damaged log events, it stops work right away. This stop protects your replica tables from bad writes and missing rows. Teams must find the exact break point to restore normal data flow.
What causes mysql error 1610 in database clusters
The official symbol for mysql error 1610 is ER_SLAVE_CORRUPT_EVENT under SQLSTATE HY000. The database engine outputs a message stating that a corrupted replication event was detected. This stop happens when the replica SQL thread cannot read the local relay log.
Network drops between the primary server and the replica often damage data in transit. If packets get scrambled on the wire, the relay log stores broken bytes. Disk failures on either host also ruin log files before the replica reads them.
Memory faults on the primary node can corrupt events before the network sends them. Sometimes a sudden power loss cuts off a write to the binary log. When the replica pulls that half-written event, the parser fails and raises code 1610.
Version mismatches between cluster nodes also cause this issue during upgrades. A newer primary server might write an event format that an older replica rejects. Checking event checksums helps catch these bad bytes early.
How to diagnose the corrupted event
Start by checking the replica status output to find the exact coordinates of the failure. Look for the primary binary log file name and the last good read position. The status report shows where the SQL thread stopped working.
Next, inspect the error log on the replica server for details around the crash time. This log tells you if the fault sits in the relay log or primary log. Compare the event data on both hosts to isolate the source of the damage.
MySQL Access Governance + End-to-End Encryption: architecture patterns and best practices
Continue reading? Get the full guide.
Free. No spam. Unsubscribe anytime.
If the primary binary log is clean, the break happened during transit or local disk writes. If the primary log is also unreadable at that offset, the primary host caused the fault. Check your host disk health and system memory logs right away.
How to fix the replication failure in production
When the primary log is intact, you can fix the replica by clearing its relay logs. Stop the replica threads and point the replica back to the last executed primary position. Start the replica threads again so the server fetches fresh copies of the events.
Never skip the broken event without knowing what data it holds. Skipping events leaves silent gaps in your replica tables and breaks data accuracy. Avoid granting broad admin rights to your team during an outage.
If the primary binary log is broken, fetching the relay log again will not work. You must rebuild the replica from a clean backup or a fresh data snapshot. After the restore finishes, point the replica to a new binary log file on the primary.
Turn on binary log checksums so the cluster verifies every event from start to finish. Checksums help the replica spot network damage before writing bad bytes to the relay log. Keep strict role rules in place while your team runs these recovery steps.
Check MySQL queries and results on the wire
MySQL grants control who logs in. They do not check single queries or mask sensitive columns once a session starts. With hoop.dev, you run an open-source proxy, a sidecar for your MySQL, inline in the MySQL wire protocol. On every query an AI agent or human runs against production MySQL, RDS, or Aurora, hoop.dev decides to pass, mask, block, or hold it for review.
Multi-statement batches and prepared queries are split and checked one by one by hoop.dev guardrails, which refuse banned queries with a native MySQL error or hold risky ones for approval. On the response path, hoop.dev data masking rewrites string values in returned rows in memory, and every decision is logged. See the MIT-licensed project on GitHub.
Frequently asked questions
What does ER_SLAVE_CORRUPT_EVENT mean in MySQL?
It means the replica found unreadable data inside a binary log or relay log event. The database stops replication right away to keep bad data out of your tables.
Can I skip a corrupted event to fix mysql error 1610?
Skipping an event is risky because your replica will miss a real data change. It is much safer to fetch a clean log from the primary or rebuild the replica.
How do I stop relay log corruption from happening again?
Enable binary log checksums on both the primary and replica servers. You should also check your disk health and set the replica to recover relay logs on startup.
Related guides
In this post